Airpura complete replacement filter kit by purifier model
The Airpura Complete Replacement Filter Kit groups the major model-specific replacement components into one convenient package. Choose the exact purifier model to receive the correct filter sizes, carbon formulation, and particle-filter type.
Choose by purifier model: Match the model printed on the serial label on the back of your Airpura unit to the variant selector before ordering.
What this replacement filter does
R, V, and F kits combine a prefilter, model-specific carbon filter, and H13 True HEPA filter. The C700DLX kit uses a prefilter, 26 lb carbon filter, and HEPA Barrier. The T700DLX kit uses a TarBarrier, 26 lb carbon filter, and HEPA Barrier. The UV700 kit also includes the compatible UV-C lamp.
Compatible Airpura models
Available for R400, V400, R700, V700, F700, C700DLX, T700DLX, and UV700. Kits are model-specific and should be matched to the serial label on the back of the purifier.
Where it goes
The outer prefilter or TarBarrier sits against the chamber wall. The carbon canister sits inside it, with the True HEPA or HEPA Barrier assembly inside the carbon canister. The UV700 kit also includes the internal UV lamp. Match the kit to the model on the purifier’s rear label.
Specifications and maintenance
| R/V/F models |
Prefilter + model-specific carbon + H13 True HEPA |
| C700DLX |
Prefilter + 26 lb carbon + HEPA Barrier |
| T700DLX |
TarBarrier + 26 lb enhanced carbon + HEPA Barrier |
| UV700 |
Prefilter + 18 lb carbon + H13 True HEPA + UV-C lamp |
| Installation |
Outer prefilter or TarBarrier, carbon canister, then central particle filter; UV700 also has an internal lamp |
Replacement intervals are manufacturer guidelines. Actual service life varies with air quality, operating speed, and hours of use.
Installation steps
Match the replacement to the model on the purifier’s rear label. Switch off and unplug before starting; retain all felt gaskets and screws for reassembly.
Filter arrangement: R400, V400, R700, V700 and F700 use an outer prefilter, carbon and True HEPA. C700DLX uses an outer prefilter, carbon and a HEPA Barrier. T700DLX uses a TarBarrier, carbon and a HEPA Barrier. UV700 uses an outer prefilter, carbon, True HEPA and an internal lamp.
Installing your replacement filter kit
- Switch off and unplug the purifier. Support the unit securely while turning it over to access the base.
- Remove the four retaining screws, lift off the bottom cover and set aside the upper felt gasket. Keep the screws and gaskets for reassembly.
- Remove the old filter components and retain the felt gaskets. Keep any fitted particle wrap and securing bands with the corresponding replacement assembly.
- Place the lower felt gasket flat at the bottom of the chamber and position the outer prefilter or TarBarrier against the chamber wall.
- Roll the filter slider into a spiral, insert it inside the outer filter and open its top into a slight funnel.
- Hold the correct carbon canister straight and lower it through the slider. Lift the slider out with both hands, allowing the canister to settle at the bottom. Remove and retain the slider.
- Insert the correct True HEPA or HEPA Barrier assembly inside the carbon canister. Retain any fitted particle wrap and its securing bands in their original positions.
- Replace the upper felt gasket. Align the indentation in the bottom cover with the center of the particle filter, refit the cover and tighten all four screws.
- Return the purifier upright. Reconnect power only after the filter chamber is closed, with the control switched off before plugging in.
Replacing the UV700 kit’s lamp
- Switch off and unplug the purifier. Support the unit securely while turning it over to access the base.
- Remove the four retaining screws, lift off the bottom cover and set aside the upper felt gasket. Keep the screws and gaskets for reassembly.
- Move any filters needed for access, noting their positions.
- Pull the old lamp upward out of its connector and press the compatible replacement lamp firmly into the connector.
- Refit any filters removed for access in their original positions. Keep the lamp enclosed during operation.
- Replace the upper felt gasket. Align the indentation in the bottom cover with the center of the particle filter, refit the cover and tighten all four screws.
- Return the purifier upright. Reconnect power only after the filter chamber is closed, with the control switched off before plugging in.
Installation manuals
Optional illustrated manuals for the compatible models are linked below.
